![atollic truestudio stm32f7 printf atollic truestudio stm32f7 printf](https://i.ytimg.com/vi/jRBdTLwnP9M/maxresdefault.jpg)
- #ATOLLIC TRUESTUDIO STM32F7 PRINTF FULL#
- #ATOLLIC TRUESTUDIO STM32F7 PRINTF CODE#
- #ATOLLIC TRUESTUDIO STM32F7 PRINTF MAC#
Heinbali01 wrote on Friday, February 08, 2019: I will also try to continue with the tutorial creating a socket, but i thought that now the stm should be visible to the Router…
#ATOLLIC TRUESTUDIO STM32F7 PRINTF FULL#
PrvEthernetUpdateConfig: LS mask 01 Force 0Īutonego ready: 00000004: full duplex 100 mbit high status XPhyReset: phyBMCR_RESET timed out ( done 0x00 ) PrvEthernetUpdateConfig: LS mask 00 Force 1 I put the log down here (i connected the ethernet cable after a few secs when the scheduler started…)
#ATOLLIC TRUESTUDIO STM32F7 PRINTF MAC#
If i do an “arp -a” I can see the ip + mac of the board.Īlso a strange behaviout: the vApplicationIPNetworkEventHook is only called when I connect the board the first time, as i wrote before. There was a spelling mistake in xRestult instead of xResult but…īut the Board is not listed in the Routers list of ips… Philipp007 wrote on Tuesday, February 05, 2019: XLength = vsnprintf( pcBuffer, sizeof pcBuffer, pcFormat, xArgs ) Void vLoggingPrintf( const char *pcFormat.
#ATOLLIC TRUESTUDIO STM32F7 PRINTF CODE#
* Code below has confirmed that the semaphore has beenĬreated and that it has been taken by vLoggingPrintf(). XResult = xSemaphoreTake( xLoggingSemaphore, xTicksToWait ) TickType_t xTicksToWait = pdMS_TO_TICKS( 100 ) XLoggingSemaphore = xSemaphoreCreateMutex() If( xTaskGetSchedulerState() = taskSCHEDULER_NOT_STARTED ) I haven’t tested this code yet: static SemaphoreHandle_t xLoggingSemaphore = NULL Here below a simple version of vLoggingPrintf() that is task-safe. That has to do with the fact that a FreeRTOS task may not call any Windows System API’s like printf() and fflush(). The Windows project indeed has a separate (Windows) thread that prints a queue of logging lines. It is called when a packet has been received or when it has been sent. Most Network Interface’s are defining an EMAC interrupt. Heinbali01 wrote on Tuesday, February 05, 2019: (static stm ip is 192.168.55.149).ĭo you have any Idea what could causes this problem? If I use the ipconfigUSE_DHCP 1 the debugger says vDHCPprocess: discover. The Router also dont recognize the device and I cant ping it. Also no call when reconnecting the cable. But the vApplicationIPNetworkEventHook is not called again after x secs or also (as described in the API) when the cable disconnects. If I connect the stm32 with the router the eNetworkEvent is recognized as eNetworkUp. (worse porblem) After calling FreeRTOS_IPInit(…) with a static IP Adresse vApplicationIPNetworkEventHook is called every ~2 seconds.
![atollic truestudio stm32f7 printf atollic truestudio stm32f7 printf](http://www.emcu.eu/wp-content/uploads/2018/02/A5-300x136.png)
Void FreeRTOS_TCP_SWO_debug(const char *s) I use for both prints (debug and non debuging messages) an SWV the function: ipconfigHAS_DEBUG_PRINTF with 1 works just fine. It stucks inside HardFault_Handler in stm32f7xx_it.c while loop and blocks other tasks. (not so bad) When I set ipconfigHAS_PRINTF in FreeRTOSIPconfig.h to 1 my application hangs. Philipp007 wrote on Monday, February 04, 2019: